This datasheet has been download from: Datasheets for electronics components. LM datasheet, LM circuit, LM data sheet: NSC – LMC Voltage Controlled Oscillator,alldatasheet, datasheet, Datasheet search site for Electronic. LM National Semiconductor datasheet pdf data sheet FREE Datasheets (data sheet) search for integrated circuits (ic), semiconductors and other electronic.

Author: Goltilabar Yojinn
Country: Comoros
Language: English (Spanish)
Genre: Music
Published (Last): 5 September 2008
Pages: 200
PDF File Size: 9.66 Mb
ePub File Size: 1.59 Mb
ISBN: 158-3-23281-618-5
Downloads: 31074
Price: Free* [*Free Regsitration Required]
Uploader: Doulmaran

If you build the VCO, you need to be aware that if you make an error, it’s quite likely that you’ll get no output at all.

It’s actually a clever design, and relies on U1A to integrate the source modulating voltage to produce a positive-going linear ramp. The reason for using a dataxheet like those shown below is – first and foremost – to be able to get a passable sinewave output.

If you’re not too worried about minimising distortion. You may be able to find them advertised on certain on-line auction sites, but they are not trustworthy sources and you have no idea what you’ll get.

The output voltage may be stuck at zero or around 10V. An opamp VCO circuit is shown in the LM opamp datasheet, and that’s the basis for the design shown here. Is your intent just simulation or do you want to lay out a PCB? There aren’t many alternatives lmm566.

Sensitivity is halved because the effective supply voltage has been doubled compared to the single supply version shown in Figure 2. If you only need a low frequency VCO, this is the easiest way to build one. Email Required, but never shown.

The resistors around the input are designed to ensure that the positive and negative integration times are identical, hence R3A and R3B in parallel because the exact half value isn’t available in most resistor series. Positive feedback is used to ensure that the triangle wave has a defined peak-to-peak voltage.

  CFDOCUMENT PAGE BREAK PDF

LM566 Datasheet

It’s been assumed that you need a VCO with a triangle wave output that can be converted to a sinewave, and a squarewave with equal mark-space ratio. This isn’t something I intend to include, and if that’s what you need you’ll have to look at designs specifically intended for use with synthesisers.

I need a dtasheet that does just the function 2 Datasheet of UTC http: Reproduction or re-publication by any means whatsoever, whether electronic, mechanical or electro-mechanical, is strictly prohibited under International Copyright laws. It is possible to recreate this in Multisim in a top level schematic using ideal components to eatasheet if it gives you the desired results with the shown external parts as well.

Voltage Controlled Oscillator jojo July 29, 4 Comments. The base frequency can be set by a pot as shown, and the modulation signal is symmetrical around zero volts.

LM National Semiconductor, LM Datasheet

The LM circuit is shown above. This will change slightly depending on the load and the ICs internal temperature. The output of U1A and U1B are more or less symmetrical around zero.

Message 4 of 7. Because most are unable to pull the output voltage down to the negative supply, we need to add an extra resistor R9, Figure 3 to ensure that the transistor Q1 will turn on and off properly. Using a ground reference for the input stage of a dual supply version also means that the modulating voltage Dtasheet, DC or a combination of the two must always be positive. The datasheet shows a formula for frequency, and with the values given in Figure 1 it works out to be 1kHz if the ‘Set Base Frequency’ pot is set for 6V.

LM Datasheet pdf – LMC Voltage Controlled Oscillator – National Semiconductor

Message 2 of 7. The datasjeet level and distortion will change with temperature. Message 1 of 7. The output frequency of the VCO can be obtained using the following equation: Most Active Software Boards: The maximum frequency is also limited, so these circuits can’t be used for RF applications. It can be done using discrete transistors, but the om566 result would be quite complex, difficult to build, and would almost certainly have issues with thermal stability.

  GRUNDLAGEN VON DATENBANKSYSTEMEN ELMASRI PDF

Another application of the voltage controlled oscillator is the variable frequency signal generator itself. Changing the Schmitt trigger resistors will change the output level of the triangle wave, which will affect the distortion when the diode clipper is used to obtain a sinewave.

Datasheets search archive of electronic components datasheets

You may also like: Linear voltage controlled oscillators are generally used to produce a sine wave. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to lm5666 policies.

The datasheet shows a pair datashewt fixed resistors, but I’ve shown a pot that lets you set the base frequency.

Here a varactor varicap diode is used in place of the capacitor in the tank circuit. The modulation input will cause the frequency to change by a factor that is directly related to the input level. The control voltage input needs to be biased to some voltage that gives you the datashest frequency you need. The l566 of circuits like those shown here is that there are no glitches in the output, no matter how quickly or slowly the frequency is changed.

Message 3 of 7. This applies whether the circuit datashewt operated from a single or a dual supply. While using a single supply, the supply voltage range is from 10V to 24V. The only thing you can do is to check all wiring very carefully, secure in the knowledge that if everything is wired exactly as shown, it will work.